Burkert – Type S077 Positive Displacement Sensor Fitting for Continuous Flow Measurement

Positive displacement sensor fitting for continuous flow measurement

This positive displacement sensor fitting is specially designed for flow measurement and/or batch control of highly viscous fluids like glue, honey or oil.

This measuring element must be associated to a transmitter SE30, SE32, SE35 or SE36 with hall sensor principle only, quickly and easily connected together by a Quarter-Turn.

The design of this fitting is based on the oval rotor principle. This has proven to be a reliable and highly accurate volumetric method of measuring flow.

Exceptional repeatability and high accuracy over a wide range of viscosities and flowrates are features of that design. The low pressure drop and high pressure rating make it suitable for both gravity and pump (inline) applications

type s077

• Burkert - Type 8077 Flowmeter with Oval Rotors
• Burkert - Type SE30 - Inline Sensor Fitting with Paddle Wheel for Flow Measurement
• Burkert Type SE32 Transmitter for Inline Sensor Fitting
• Burkert Type SE35 Transmitter or Batch Controller for Inline Sensor Fitting
• Burkert - Type SE36 ELEMENT Transmitter for Inline Sensor Fitting

General Technical Data

Product properties
Materials	Please make sure the device materials are compatible with the fluid you are using. Detailed information can be found in chapter “3.1. Chemical Resistance Chart – Bürkert resistApp” on page 4.
Wetted parts
Body	Aluminium, stainless steel 316L (1.4401)
Seal	FKM or FEP/PTFE encapsulated
Oval gears	Stainless steel 316L (1.4401)
Shaft	Stainless steel 316L (1.4401)
Dimensions	Detailed information can be found in chapter “4. Dimensions” on page 5.
Measuring principle	Oval gear
Compatibility	With transmitter SE30, SE32, SE35, SE36 with Hall sensor principle Detailed information can be found in the respective technical data sheets, see data sheets Type SE30 + S077 , Type SE32 + S077 , Type SE35 + S077 , Type SE36 + S077  for more information.
Pipe diameter	DN 15…DN 100
Measuring range	• Viscosity > 5 mPa.s: 2…1200 l/min (0.53…320 gpm) • Viscosity < 5 mPa.s: 3…616 l/min (0.78…320 gpm)
Performance data
Measurement deviation	• With K-factor determined with a teach-in procedure or with the specific K-factor, engraved on the sensor fitting: ± 0.5 % of the measured value (at Teach-In flow rate value) • With standard K-factor: ± 1 % of the measured value
Repeatability	± 0.03 % of the measured value
Medium data
Fluid temperature	With sensor fitting S077 in: • Aluminium: – 20…+ 80 °C (- 4…+ 176 °F) • Stainless steel: – 20…+ 120 °C (- 4…+ 248 °F)
Fluid pressure (max.)	With sensor fitting S077 in: • DN 15: 55 bar (798.05 PSI) (threaded process connection) • DN 25: 55 bar (798.05 PSI)1.) • DN 40 or DN 50: 18 bar (261.18 PSI) • DN 80: 12 bar (174.12 PSI) • DN 100: 10 bar (145.1 PSI)
Viscosity	Max. 1 Pa.s (higher on request)
Rate of solid particles	0 %
Process/Port connection & communication
Process connection	• Thread: ½”; 1″; 1½”; 2″; 3″ (G or NPT) • Flange: – 25; 40; 50; 80 or 100 mm DIN PN 16 flange – 1″; 1½”; 2″; 3″ or 4″ ANSI 150LB flange
Approvals and certificates
CE directives2.)	The applied standards, which verify conformity with the EU Directives, can be found on the EU Type Examination Certificate and/or the EU Declaration of conformity (if applicable)
Pressure Equipment Directive	Complying with Article 4, Paragraph 1 of 2014/68/EU directive Detailed information on the pressure equipment directive can be found in chapter “2.1. Pressure Equipment Directive” on page 4.
Environment and installation
Ambient temperature	Operation and storage: 0…+ 60 °C (+ 32…+ 140 °F)

*For selecting thecorrect product please refer to the technical data, images and notes for proper use according to the data sheet, or contact Flu-Tech directly.

สอบถามข้อมูลเพิ่มเติม ติดต่อเรา :

  02-384-6060 (อัตโนมัติ)    [email protected]    บริษัท ฟลูเทค จำกัด Flu-tech    @flutech.co.th