Burkert – Type MS06 – Flow Injection Analysis (FIA) Sensor Cube for Iron Content

Flow injection analysis (FIA) sensor cube for iron content

Bürkert has developed an FIA (flow injection ­analysis ) module for the measure of dissolved iron (Fe2+/Fe3+) for use in the online analysis system, which combines all necessary components including control in a minimum of space.

type ms06

General Technical Data

Product properties
Material	Please make sure the device materials are compatible with the fluid you are using. Detailed information can be found in chapter “2.1. Chemical Resistance Chart – Bürkert resistApp” on page 5.
Housing	Polycarbonate
Backplane	Anodized aluminium
Lever	Stainless steel
Wetted parts	EPDM, FKM, NBR, PMMA, PEEK
Valve	FFKM
Seals	EPDM, FKM or NBR
Dimensions	Detailed information can be found in chapter “3. Dimensions” on page 5.
Weight	1.05 kg
Measuring principle	Flow injection analysis (dissolved iron) with photometric detection
Temperature sensor	Pt1000
Compatibility	With Reagent unit Type MZ30 and Online Analysis System Type 8905 Detailed information can be found in the data sheet of the reagent unit and of the online analysis system, see data sheet Type MZ30 and data sheet Type 8905 for more information.
Measuring range	0…2 mg/l – higher range on request (max. 10 mg/l)
Maintenance
Calibration period	Automatic or manual
Waste	Error on waste full
Exchange of reagents	Depends on analysis interval
Performance data
Minimum detection limit	0.02 mg/l
Measuring range resolution (internal)	0.001 mg/l at 0.05 mg/l 0.01 mg/l at 10 mg/l
Measurement deviation	± 0.05 mg/l or 5 %
Linearity	± 3 % of full scale
Repeatability	± 3 % of full scale
Measuring cycle time	Minimum 60 min.
Electrical data
Operating voltage	24 V DC through the backplane of the system Type 8905 via büS
Power consumption	2.2 (Standby)…12.7 W
Medium data
Fluid	Water without particles: drinking water, industrial water
pH value	pH 4…pH 9
Sample water
Temperature	+ 3…+ 40 °C (+ 37…+ 104 °F)
Pressure	PN3
Flow rate	> 6 l/h
Sample water filter	>100 µm
Process/Port connection & communication
Process connection	Via pinch valve in the fluidic backplane of the Type 8905 Detailed information can be found in the data sheet of t the Online Analysis System, see data sheet Type 8905 for more information.
Electrical connection	Spring contacts in the fluidic backplane of the Type 8905, which is connected to a büS System. Detailed information can be found in the data sheet of t the Online Analysis System, see data sheet Type 8905 for more information.
Data transfer
Internal communication	Through büS (Bürkert bus, CANopen protocol)
External communication by status LED	According to NAMUR NE 107
Approvals and Certificates
Degree of protection according to  IEC/EN 60529	• IP65, when plugged in the fluidic backplane • IP20, as standalone product
Directives CE directives	The applied standards, which verify conformity with the EU Directives, can be found on the EU Type Examination Certificate and/or the EU Declaration of conformity (if applica-ble).
Environment and installation
Ambient temperature Operating	+ 10…+ 40 °C (+ 50…+ 104 °F), 20 °C (+ 68 °F) recommended
Storage and transport	• Used iron measuring module: + 10…+ 30 °C (+ 50…+ 86 °F) • For empty/purged sensor cube: – 10…+ 60 °C (+ 14…+ 140 °F)
Relative air humidity	≤ 90 %, without condensation
Height above sea level	Max. 2000 m
Operating condition	Continuous
Equipment mobility	Fixed
Application range	Indoor and outdoor (Protect the device against electromagnetic interference, ultraviolet rays and, when installed outdoors, against the effects of climatic conditions)
Installation category	Category I according to UL/EN 61010-1
Pollution degree	Degree 2 according to UL/EN 61010-1

 

*For selecting thecorrect product please refer to the technical data, images and notes for proper use according to the data sheet, or contact Flu-Tech directly.

 

สอบถามข้อมูลเพิ่มเติม ติดต่อเรา :

  02-384-6060 (อัตโนมัติ)    [email protected]    บริษัท ฟลูเทค จำกัด Flu-tech    @flutech.co.th