ข้ามไปยังเนื้อหา
Flowmeter for the continuous measurement of water
The Type 8081 ultrasonic flowmeter is intended for the flow measurement of water which may be slightly charged with contaminants. It consists of an electronic module and a brass fitting with a built-in measuring tube. In combination with a controller and a control valve, it enables very simple flow control loops to be established. The electrical connection is made via a 5 pin M12 fixed connector.
DOWNLOAD CATALOG (ดาวน์โหลดแคตตาล็อก)
TYPE 8081 สามารถใช้ได้ร่วมกับ
-
Burkert - Type 8032 Flowmeter / Threshold Detector with Paddle Wheel
-
Burkert - Universal Process Controller Type 8611
-
Burkert - Type 8802 - Continuous control Valve Systems Overview (Type ELEMENT)
-
Burkert - Type 8619 multiCELL Multi Channel and Multi Function Transmitter / Controller
General Technical Data
Product properties |
|
| Materials | Please make sure the device materials are compatible with the fluid you are using. Detailed information can be found in chapter “3.1. Chemical Resistance Chart – Bürkert resistApp” on page 5. |
| Non wetted parts | |
| Housing | PPS |
| Cover | PA |
| Screws | Stainless steel |
| Fixed connector M12 | Silicone |
| Wetted parts | |
| Fitting | Brass |
| Measuring tube | PES |
| Seal | EPDM |
| Dimensions | Detailed information can be found in chapter xxx. |
| Measuring element | 2 ultrasound emitter-receiver cells |
| Measuring range | 0.06…200 l/min |
| Pipe diameter | DN15…DN25 |
Performance data |
|
| Measurement deviation | Flowrate: ≤ (0.01 % of full scale + 2 % of measuring value)1.) Detailed information can be found in chapter “5.1. Measurement deviation diagram” on page 6. |
| Repeatability | ≤ 1 % |
Electrical data |
|
| Operating voltage | 12…36 V DC |
| Current consumption | • Own consumption: < 4 mA • Consumption with load: < 1 A |
| Output signal | The device is available with a pulse output or with a pulse output and a 4…20 mA ana-logue outputs • Device with a pulse (transistor) output: – Pulse (transistor): NPN (as default setting) or PNP (on request), open collector NPN-output: 0.2…36 V DC, max. 700 mA, min. 5 mA Galvanic insulation and protected against overvoltage, polarity reversals and short circuit • Device with a pulse (transistor) and a 4…20 mA analogue outputs: – Pulse (transistor): PNP (as default setting) or NPN (on request), open collector PNP-output: operating voltage (V+), max. 700 mA Galvanic insulation and protected against overvoltage, polarity reversals and short circuit – Current: 4…20 mA (sourcing mode and PNP transistor as default setting, sinking mode and NPN transistor on request) Loop impedance max.: 1100 Ω at 36 V DC; 610 Ω at 24 V DC; 100 Ω at 12 V DC |
| Scaling | • Pulse (transistor): – If model QN 0.6 or QN 1.5 : 1 pulse corresponds to a volume = 0.002 l (K factor = 500 pulse/litre) – If model QN 2.5 or QN 3.5 : 1 pulse corresponds to a volume = 0.005 l (K factor = 200 pulse/litre) – If model QN 6 : 1 pulse corresponds to a volume = 0.01 l (K factor = 100 pulse/litre) • Current: 4 mA correspond to 0 l/min and 20 mA correspond to Qmax. of flow range (by default) |
| Voltage supply cable | 1.5 mm2 max. cross-section |
Medium data |
|
| Temperature | + 5…+ 90 °C (+ 41…+ 194 °F) |
| Pressure | PN16 (232.16 PSI) |
Process/Port connection & communication |
|
| Process connection | G or NPT external thread; ¾”, 1″ or 1″¼ |
| Electrical connection | 5 pin M12 male fixed connector for female 5 pin M12 cable plug (not provided) |
Approvals and certificates |
|
| Standards Protection class according to IEC/EN 60529 |
IP65 with M12 cable plug plugged-in and tightened |
| CE directives | The applied standards, which verify conformity with the EU Directives, can be found on the EU Type Examination Certificate and/or the EU Declaration of conformity (if applicable) |
| Pressure equipment directives | Complying with Article 4, Paragraph 1 of 2014/68/EU directive Detailed information on the pressure equipment directive can be found in chapter “2.1. Pressure Equipment Directive” on page 4. |
| Certificate | On request: • Test report 2.2 • Calibration certificate |
Environment and installation |
|
| Ambient temperature | Operating and storage: + 5…+ 55 °C (+ 41…+ 131 °F) |
| Relative air humidity | ≤ 80 %, without condensation |
| Height above sea level | Max. 2000 m |
*For selecting thecorrect product please refer to the technical data, images and notes for proper use according to the data sheet, or contact Flu-Tech directly.
สอบถามข้อมูลเพิ่มเติม ติดต่อเรา :
02-384-6060 (อัตโนมัติ) [email protected] บริษัท ฟลูเทค จำกัด Flu-tech @flutech.co.th