Skip to content
Transmitter or batch controller for Inline sensor-fitting
DOWNLOAD CATALOG (ดาวน์โหลดแคตตาล็อก)
BURKERT TYPE SE35 สามารถใช้ได้ร่วมกับ
-
Burkert - Type S030 Inline Sensor Fitting with Paddle Wheel for Flow Measurement
-
Burkert - Type S077 Positive Displacement Sensor Fitting for Continuous Flow Measurement
General Technical Data
Product properties |
|
| Material | Please make sure the device materials are compatible with the fluid you are using. Detailed information can be found in chapter “3.1. Chemical Resistance Chart – Bürkert resistApp” on page 7. |
| Non wetted parts | |
| Housing, cover | PC |
| Lid | PC |
| Front panel foil | Polyester |
| Screws | Stainless steel |
| fixed plug | • Body, contact holder and cable gland in PA • Cable gland seal and flat seal in NBR |
| Cable glands | PA |
| Quarter turn system | PC |
| Wetted parts | |
| Sensor-fitting body | Aluminium or stainless steel (316L) |
| Seal | FKM or FEP/PTFE encapsulated |
| Oval gear | PPS, aluminium or stainless steel (316L) |
| Shaft | Stainless steel (316L) |
| Dimensions | Detailed information can be found in chapter “4. Dimensions” on page 9. |
| Measuring principle | Oval gear |
| Compatibility | Any pipe from DN 15…DN 100 which is fitted with Bürkert S077 Inline sensor-fitting. For the selection of the nominal diameter of the Inline sensor-fittings, see data sheet Type S077 . |
| Display | 15 × 60 mm, 8-digit LCD, alphanumeric,15 segments, 9 mm high |
| Pipe diameter | DN 15…DN 100 |
| Measuring range | • Viscosity > 5 mPa.s: 2…1200 l/min (0.53…320 gpm) • Viscosity < 5 mPa.s: 3…616 l/min (0.78…320 gpm) |
Performance data |
|
| Measurement deviation | • With K-factor determined with a teach-in procedure or with the specific K-factor, engraved on the sensor-fitting: ± 0.5 % of the measured value (at Teach-In flow rate value) • With standard K-factor: ± 1 % of the measured value |
| Repeatability | ± 0.03 % of the measured value |
Electrical data |
|
| Power source (not supplied) | Limited power source according to UL/EN 60950-1 standards or limited energy circuit according to UL/EN 61010-1 §9.4 |
| Protection against DC polar-ity reversal | Yes |
| Overvoltage protection | Yes |
| Voltage supply cable | • Cable with maximum operating temperature greater than 80 °C (90 °C for UL-Recognized version) • Max. 50 m length, shielded |
Medium data |
|
| Fluid temperature | With sensor-fitting S077 in: • Aluminium: – 20…+ 80 °C (- 4…+ 176 °F) • Stainless steel: – 20…+ 120 °C (- 4…+ 248 °F) See data sheet Type S077 for more information. |
| Fluid pressure (max.) | • DN 15: 55 bar (798.05 PSI) (threaded process connection) • DN25: 55 bar (798.05 PSI)1.) • DN40 or DN50: 18 bar (261.18 PSI) • DN80: 12 bar (174.12 PSI) • DN100: 10 bar (145.1 PSI) See data sheet Type S077 for more information. |
| Viscosity | Max. 1 Pa.s (higher on request) |
| Rate of solid particles | 0% |
Process/Port connection & communication |
|
| Process connection | • Thread: ½”; 1″; 1½”; 2″; 3″ (G or NPT) • Flange: – 25; 40; 50; 80 or 100 mm DIN PN16 flange – 1″; 1½”; 2″; 3″ or 4″ ANSI 150LB flange |
Approvals and Certificates |
|
| Standards Degree of protection2.) according to IEC/EN 60529 |
IP65 with device wired and plugs mounted and tightened |
| Directives CE directives |
The applied standards, which verify conformity with the EU Directives, can be found on the EU Type Examination Certificate and/or the EU Declaration of conformity (if applicable) |
| Pressure equipment directives | Complying with Article 4, Paragraph 1 of 2014/68/EU directive Detailed information on the pressure equipment directive can be found in chapter “2.2. Pressure Equipment Directive” on page 7. |
| Certification | UL-Recognized for US and Canada |
Environment and installation |
|
| Relative air humidity | ≤ 80 %, without condensation |
| Height above sea level | Max. 2000 m |
| Operating condition | Continuous |
| Equipment mobility | Fixed |
| Application range | Indoor and outdoor (protect the device against electromagnetic interference, ultraviolet rays and against the effects of climatic conditions) |
| Installation category | Category I according to UL/EN 61010-1 |
| Pollution degree | Degree 2 according to UL/EN 61010-1 |
*For selecting thecorrect product please refer to the technical data, images and notes for proper use according to the data sheet, or contact Flu-Tech directly.
สอบถามข้อมูลเพิ่มเติม ติดต่อเรา :
02-384-6060 (อัตโนมัติ) [email protected] บริษัท ฟลูเทค จำกัด Flu-tech @flutech.co.th