Add to wishlist
Burkert-Type 8036 เครื่องวัดการไหลของของเหลวแบบใบพัด (Paddle Wheel Flow Meters)

Burkert – Type 8036 ELEMENT Design Inline Flowmeter with Paddle Wheel

จุดเด่นของ Type 8036

  • Size of measurement pipes: DN 06 to DN 65
  • Configurable outputs: one or two transistor output(s) and one or two 4…20 mA current output(s)
  • Automatic calibration using Teach-In, all outputs can be checked without the need for actual flow
  • Removable backlit display/configuration module for indication of flow rate and volume with two flow totalizers
Send Email LINE OA
Categories: ,

Inline flowmeter with paddle wheel, ELEMENT design

The flowmeter Type 8036 is a compact device, specially designed for measur-ing the flow rate in solid-free liquids, in a variety of applications (water, waste water monitoring, chemical processing, etc.).
Type 8036 is available with:

  • 2 configurable outputs: one transistor output (NPN) and one 4…20 mA current output (2-wire)
  • 3 configurable outputs: two transistor outputs (NPN/PNP) and one 4…20 mA current output (2-wire)
  • 4 configurable outputs: two transistor outputs (NPN/PNP) and two 4…20 mA current outputs (3-wire)

Type 8036 converts the measured signal, displays different values in different units (if display/configuration module mounted) and computes the output signals, which are provided via one or two M12 fixed connectors. Thanks to 1 or 2 transistor outputs, the flowmeter can be used to switch a solenoid valve, activate an alarm and, thanks to 1 or 2 current outputs, establish one or two control loops.

DOWNLOAD CATALOG (ดาวน์โหลดแคตตาล็อก)

type 8036

BURKERT TYPE 8036 สามารถใช้ได้ร่วมกับ

General Technical Data

Product properties
Non wetted parts
Housing Stainless steel 1.4404 (316L), PPS
cover Polycarbonate (PC), transparent (opaque on request)
Display/configuration module PC
Navigation key PBT
Seals EPDM, silicone
Screws Stainless steel 1.4401 (316 (A4))
Fixed connector holder PPS CF30
Fixed connector Nickel-plated brass (stainless steel on request)
Wetted parts
Sensor-fitting body, sensor armature Brass, stainless steel, PVC, PP or PVDF (depending on S030 version)
Seal FKM or EPDM (depending on S030 version)
Axis and bearings Ceramics (Al2O3)
Paddle wheel, holder PVDF
Dimensions Detailed information can be found in chapter “4. Dimensions” on page 6
Measuring element Paddle wheel
Compatibility Any pipe from DN 06…DN 65 which is fitted with Bürkert S030 Inline sensor-fitting.For the selection of the nominal diameter of the Inline sensor-fittings, see data sheet Type S030 .
Pipe diameter DN 06…DN 65
Measuring range • Flow rate: 0.5…1200 l/min (0.13…320 gpm)• Flow velocity: 0.3…10 m/s

Performance data
Measurement deviation Teach-In: ± 1 % of the measured value1.) (at Teach-In flow rate value) Standard K-factor: ± 2.5 % of the measured value1.)
Repeatability ± 0.4 % of the measured value2.)
Linearity ± 0.5 % of full scale2.)
4…20 mA output uncertainty ± 1 % of range

Electrical data
Operating voltage • 2 or 3 outputs transmitter (2-wire) version: 14…36 V DC, filtered and regulated• 4 outputs transmitter (3-wire) version: 12…36 V DC, filtered and regulatedConnection to main supply: permanent (through external SELV (Safety Extra Low Voltage) and LPS (Limited Power Source) power supply
Power source (not supplied) Limited power source according to UL/EN 60950-1 standards or limited energy circuit according to UL/EN 61010-1 §9.4
DC reverse polarity protection Yes
Over-voltage protection Yes
Current consumption With sensor• ≤ 1 A (with transistors load)• 2 or 3 outputs transmitter (2-wire) version: ≤ 25 mA (at 14 V DC without transistors load, with current loop)• 4 outputs transmitter (3-wire) version: ≤ 5 mA (at 12 V DC without transistors load, without current loop)
Power consumption Max. 40 W
Outputs
Transistor Protected against overvoltage, polarity reversals and short circuit•1 transistor output (transmitter 2-wire):– NPN, open collector– 1…36 V DC– Max. 700 mA•2 transistor outputs (transmitter 2 or 3-wire):–  Adjustable as sourcing or sinking (respectively both as PNP or NPN ), open collector–  Max. 700 mA–  0.5 A max. per transistor if the 2 transistor outputs are wired–  NPN-output: 1…36 V DC–  PNP-output: Power supply
Current 4…20 mA adjustable as sourcing or sinking (in the same mode as transistor):• 1 current output (transmitter 2-wire)Max. loop impedance: 1100 Ω at 36 V DC; 610 Ω at 24 V DC; 180 Ω at 14 V DC• 2 current outputs (transmitter 3-wire)Max. loop impedance: 1100 Ω at 36 V DC; 610 Ω at 24 V DC; 100 Ω at 12 V DC
Voltage supply cable For the female M12 connector and/or the male M12 connector (not supplied, to order separately, see chapter “10.5. Ordering chart accessories” on page 11) use a shielded cable.• Ø 3…6.5 mm• Cross section of wires: max. 0.75 mm²

Medium data
Fluid temperature With sensor-fitting S030 in:• PVC: 0…+ 50 °C (+ 32…+ 122 °F)• PP: 0…+ 80 °C (+ 32…+ 176 °F)• PVDF, stainless steel or brass: – 15…+ 100 °C (+ 5…+ 212 °F) See data sheet Type S030 for more information.
Fluid pressure (max.) With sensor-fitting S030 in:• plastic: PN 10• metal: PN 16 (PN 40 on request)See data sheet Type S030 for more information.
Viscosity Max. 300 cSt
Rate of solid particles Max. 1 % .
Maximum particle size 0.5 mm

Process/Port connection & communication
Process connection With sensor-fitting S030 in:• plastic: true union, spigot or external thread• metal: internal or external thread, weld ends, Clamp or flange See data sheet Type S030 for more information.
Electrical connection  • 2 or 3 outputs transmitter (2-wire) version: 1 x 5 pin M12 male fixed connector• 4 outputs transmitter (3-wire) version: 1 x 5 pin M12 male and 1 x 5 pin M12 female fixed con-nectors

Approvals and certificates
StandardsDegree of protection2.) IP65, IP67 (according to IEC/EN 60529), NEMA 4X (according to NEMA250) with device wired and M12 cable plug mounted and tightened and cover fully screwed down
CE directives The applied standards, which verify conformity with the EU Directives, can be found on the EU Type Examination Certificate and/or the EU Declaration of conformity (if applicable)
Pressure Equipment Directive Complying with Article 4, Paragraph 1 of 2014/68/EU directiveDetailed information on the pressure equipment directive can be found in chapter “3.1. Chemical Resistance Chart – Bürkert resistApp” on page 5.
Certification UL-Recognized for US and Canada

Environment and installation
Ambient temperature Operation and storage: – 10…+ 60 °C (+ 14…+ 140 °F)
Relative air humidity ≤ 85 %, without condensation
Height above sea level Max.­2000 m
Operating condition Continuous
Equipment mobility Fixed device
Application range Indoor­and­outdoor­(protect­the­device­against­electromagnetic­interference,­ultraviolet­rays and­against­the­effects­of­climatic­conditions)
Installation category Category II according to UL/EN 61010-1
Pollution degree Degree 2 according to UL/EN 61010-1

*For selecting thecorrect product please refer to the technical data, images and notes for proper use according to the data sheet, or contact Flu-Tech directly.

สอบถามข้อมูลเพิ่มเติม ติดต่อเรา :

  02-384-6060 (อัตโนมัติ)    [email protected]    บริษัท ฟลูเทค จำกัด Flu-tech    @flutech.co.th